Teejet Matrix 840G User Manual Manuel d'utilisateur Page 41
- Page / 58
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
www.teejet.com
66
●
98-05141 R2
67
●
Off/Manual & Automatic
To switch BoomPilot between Off/Manual and
Automatic
1. Press BOOMPILOT ICON .
◄Off/Manual – Status Bar Icon will change to
Red
◄Automatic – Status Bar Icon will change to
Green .
All Booms On Mode
To turn all booms on
1. Press and hold BOOMPILOT ICON .
◄All On – Status Bar Icon will change to Yellow
.
Figure 3-32: Automatic to All Booms On Mode
mph acres
10.25
mph acres
10.25
Zoom In/Out &
Perspective
Zoom In/Out & Perspective is used to
adjust the vehicle’s view or perspective
to the horizon from vehicle view to bird’s
eye view.
To adjust the view or perspective:
1. Press
►ZOOM IN/OUT BUTTONS
►the screen to activate the icons and select the
ZOOM IN/OUT ICONS .
◄Zoom In will adjust view to vehicle
view displaying a compass on the horizon
◄Zoom Out will adjust view to bird’s eye
view
NOTE: Press & hold ZOOM IN/OUT BUTTONS
or ZOOM IN/OUT ICONS to
quickly adjust settings.
Figure 3-31: Zoom In to Out
mph acres
10.05
Swath acres
10.123
mph acres
10.25
Swath acres
10.323
mph acres
10.55
Swath acres
10.623
BoomPilot
BoomPilot is used to set BoomPilot to Off/Manual
, Automatic or All On .
NOTE: GPS is unavailable when the BOOMPILOT
ICON is gray . BoomPilot status bar icon
will be Off/Manual .
NOTE: The BOOMPILOT ICON is unavailable
if a SmartCable or Section Driver Module
(SDM) is not present. To activate the boom,
a status switch must be used. Only one
Boom Section width will be illustrated and
the Status Bar will have no icon.
Guidance with SmartCable or SDM
• Turn the controller master switch to the “On”
position. The individual boom section switches
should remain in the “Off” position.
• In areas where application is not desired,
manually turn “off” the rate controller master
switch to shut off the booms. Turn the master
switch “on” to resume application.
NOTE: This does not apply unless a SmartCable or
SDM is installed on the system.
- USER MANUAL 1
- CHAPTER 1– PRODUCT OVERVIEW 7
- SYSTEM FEATURES 7
- Matrix 840G Console 8
- SYSTEM COMPONENTS 8
- Matrix 570G Console 8
- RealView Camera 9
- Video Selector Modules 9
- GPS Antennas 9
- FieldPilot 9
- Steering Control Module 9
- 98-05141 R2 10
- CONFIGURATIONS 11
- Engage/Disengage 12
- POWER ON/OFF 13
- Start Up Sequence 14
- GENERAL OPERATION 14
- INFORMATION 14
- Page Layout and Navigation 15
- CHAPTER 2 – UNIT SETUP 16
- Lightbar 17
- Home Menu 17
- SYSTEM SETUP 17
- LED Brightness 18
- Display Mode 18
- Time Zone 19
- Language 19
- Requirements 20
- GPS Status 20
- GPS Type 20
- GPS Port 20
- LCD Brightness 21
- GGA Requirements 21
- Software Version 1.03 22
- Software Version 1.00 to 1.02 22
- Next Power Cycle 22
- Save About Information 23
- Screenshot 23
- Enable/Disable 23
- Capture an Image 23
- About/Save 23
- Four Channel VSM 24
- Eight Channel VSM 24
- BOOMPILOT/SINGLE 25
- BOOM SETUP 25
- BoomPilot Setup 25
- Number of Boom Sections 26
- Boom Section Width 26
- Delay On 26
- Delay Off 26
- VEHICLE SETUP 27
- Single Boom Setup 27
- TILT GYRO MODULE 28
- Valve Setup 30
- FIELDPILOT SETUP 30
- Autosteer 30
- Cycle Right 31
- Maximum Duty Cycle 31
- Minimum Duty Cycle 31
- Cycle Left 31
- Con gure FieldPilot 32
- Valve Test 32
- Deadband 33
- Coarse Steering Adjustment 33
- Fine Steering Adjustment 33
- Lookahead 34
- CHAPTER 3 – GUIDANCE 35
- GUIDANCE OPERATION 35
- Straight A-B Guidance 35
- GUIDANCE BAR & STATUS BAR 36
- Guidance Bar 36
- Curved A-B Guidance 36
- Circle Pivot Guidance 36
- Last Pass Guidance 36
- VEHICLE VIEW 37
- Status Bar 37
- Vehicle View 38
- Guidance Mode Select 38
- Zoom In/Out & 41
- Perspective 41
- BoomPilot 41
- Field View 42
- Field Boundary 42
- FIELD VIEW 42
- Return to Point 43
- Zoom In/Out 44
- World View 44
- Pan Mode 44
- REALVIEW GUIDANCE 44
- RealView Guidance 45
- Full Screen 45
- Guidance Over Video 45
- Steering Angle Indicator 46
- Single Camera Selection 46
- Split Camera View 47
- Guideline Adjustment 48
- CHAPTER 4 – MONITORING 49
- JOB VIEW 49
- Job Information 49
- Save Information 50
- BOOM MONITORING 51
- Boom Monitor 51
- APPENDIX A ICON REFERENCE 53
- Menu Options 53
- CHAPTER 5 – APPENDIX 53
- Unit Setup 54
- Job View 55
- Guidance Screens 55
- APPENDIX B TIME ZONES 56
- APPENDIX D UNIT 57
- SPECIFICATIONS 57
- APPENDIX C FACTORY 57
- SETTINGS & RANGES 57
Produits connexes et manuels pour Ordinateurs Teejet Matrix 840G User Manual
(2 pages)
(2 pages)
(2 pages)
(2 pages)
(2 pages)
(127 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels