Teejet Matrix 840G User Manual Manuel d'utilisateur Page 14
- Page / 58
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
www.teejet.com
14
●
98-05141 R2
15
●
Start Up Sequence
The console takes approximately 40 seconds to
power up. During this time the TeeJet Technologies
logo will be displayed (LEDs will power on and off
and brightness levels will fl uctuate.)
Figure 1-20: Power Up Screen
Once the power up sequence has cycled, the
following message is displayed:
“Would you like to clear the job data and begin a
new job?”
1. Press
►No – The previous job will resume.
►Yes – A new job will be established and all
data from previous jobs will be cleared. The
message “All job data cleared” is displayed.
Select “OK” to continue.
The splash screen will be displayed for
approximately one minute.
The splash screen lists the module’s current
software version. The information is also available
on the About screen.
NOTE: A firm touch is required when selecting or
acknowledging a screen option.
Figure 1-21: Clear Job Data Screens
Figure 1-22: Splash Screen
Matrix
v1.0
GENERAL OPERATION
INFORMATION
A fi rm touch is required when selecting a screen
icon.
On initial startup, the console will load the Vehicle
View screen as a default. All subsequent power
cycles will return to the last page viewed before
powering down.
Icons on guidance screens will be displayed and will
fade from the window after 6 seconds of inactivity. To
regain these icons, touch the screen in any location.
Figure 1-23: With and Without Icons On Screen
Press the icon of any menu item to display a
defi nition of that item. To remove the information
box, press anywhere on the screen.
Figure 1-24: Example of Information Text Box
For rapid adjustment of a setting, press and hold the
►PLUS/MINUS ICONS ,
►UP/DOWN ARROW ICONS
►ZOOM IN/OUT ICONS
►ZOOM IN/OUT BUTTONS (Matrix 840G
only).
The Zoom In/Out Buttons on the Matrix 840G
will not adjust Plus/Minus or Up/Down settings.
GPS Status Change – a pop-up warning will be
displayed for approximately 2.5 seconds. To remove
a pop-up sooner, press anywhere on the screen.
Figure 1-25: Example of GPS Status Change
- USER MANUAL 1
- CHAPTER 1– PRODUCT OVERVIEW 7
- SYSTEM FEATURES 7
- Matrix 840G Console 8
- SYSTEM COMPONENTS 8
- Matrix 570G Console 8
- RealView Camera 9
- Video Selector Modules 9
- GPS Antennas 9
- FieldPilot 9
- Steering Control Module 9
- 98-05141 R2 10
- CONFIGURATIONS 11
- Engage/Disengage 12
- POWER ON/OFF 13
- Start Up Sequence 14
- GENERAL OPERATION 14
- INFORMATION 14
- Page Layout and Navigation 15
- CHAPTER 2 – UNIT SETUP 16
- Lightbar 17
- Home Menu 17
- SYSTEM SETUP 17
- LED Brightness 18
- Display Mode 18
- Time Zone 19
- Language 19
- Requirements 20
- GPS Status 20
- GPS Type 20
- GPS Port 20
- LCD Brightness 21
- GGA Requirements 21
- Software Version 1.03 22
- Software Version 1.00 to 1.02 22
- Next Power Cycle 22
- Save About Information 23
- Screenshot 23
- Enable/Disable 23
- Capture an Image 23
- About/Save 23
- Four Channel VSM 24
- Eight Channel VSM 24
- BOOMPILOT/SINGLE 25
- BOOM SETUP 25
- BoomPilot Setup 25
- Number of Boom Sections 26
- Boom Section Width 26
- Delay On 26
- Delay Off 26
- VEHICLE SETUP 27
- Single Boom Setup 27
- TILT GYRO MODULE 28
- Valve Setup 30
- FIELDPILOT SETUP 30
- Autosteer 30
- Cycle Right 31
- Maximum Duty Cycle 31
- Minimum Duty Cycle 31
- Cycle Left 31
- Con gure FieldPilot 32
- Valve Test 32
- Deadband 33
- Coarse Steering Adjustment 33
- Fine Steering Adjustment 33
- Lookahead 34
- CHAPTER 3 – GUIDANCE 35
- GUIDANCE OPERATION 35
- Straight A-B Guidance 35
- GUIDANCE BAR & STATUS BAR 36
- Guidance Bar 36
- Curved A-B Guidance 36
- Circle Pivot Guidance 36
- Last Pass Guidance 36
- VEHICLE VIEW 37
- Status Bar 37
- Vehicle View 38
- Guidance Mode Select 38
- Zoom In/Out & 41
- Perspective 41
- BoomPilot 41
- Field View 42
- Field Boundary 42
- FIELD VIEW 42
- Return to Point 43
- Zoom In/Out 44
- World View 44
- Pan Mode 44
- REALVIEW GUIDANCE 44
- RealView Guidance 45
- Full Screen 45
- Guidance Over Video 45
- Steering Angle Indicator 46
- Single Camera Selection 46
- Split Camera View 47
- Guideline Adjustment 48
- CHAPTER 4 – MONITORING 49
- JOB VIEW 49
- Job Information 49
- Save Information 50
- BOOM MONITORING 51
- Boom Monitor 51
- APPENDIX A ICON REFERENCE 53
- Menu Options 53
- CHAPTER 5 – APPENDIX 53
- Unit Setup 54
- Job View 55
- Guidance Screens 55
- APPENDIX B TIME ZONES 56
- APPENDIX D UNIT 57
- SPECIFICATIONS 57
- APPENDIX C FACTORY 57
- SETTINGS & RANGES 57
Produits connexes et manuels pour Ordinateurs Teejet Matrix 840G User Manual
(2 pages)
(2 pages)
(2 pages)
(2 pages)
(2 pages)
(127 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels