Teejet Matrix 840G User Manual Manuel d'utilisateur Page 31
- Page / 58
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
www.teejet.com
48
●
98-05141 R2
49
●
Figure 2-65: Minimum Duty Cycle Left
Cycle Right
Cycle Right sets the minimum amount of drive
required to begin steering the vehicle to the right. .
1. Press MINIMUM DUTY CYCLE RIGHT ICON .
2. While the vehicle is moving in a slow forward
straight line motion, press the GREEN
STOPLIGHT .
3. Slowly increase the duty cycle number using the
PLUS BUTTON until the vehicle begins to
turn right.
4. Press the RED STOPLIGHT to complete the
right test.
5. Press
►PAGE RIGHT ARROW to proceed to
Maximum Duty Cycle.
►FIELDPILOT SETUP TAB to return to
main FieldPilot Setup.
NOTE: Press & hold PLUS/MINUS ICONS to
quickly adjust settings.
Figure 2-66: Minimum Duty Cycle Right
Maximum Duty Cycle
Maximum Duty Cycle sets the maximum speed that
the wheels will steer from left to right / right to left
(lock to lock). Range is 25 - 100.
NOTE: If the valve frequency is below 15 Hz (non
proportional), set the value to 100. Speed
will be established during the Valve Test.
WARNING: PINCH POINT HAZARD!
To prevent serious injury or death, avoid
unsafe practice while manually operating
hydraulic steering circuits. Keep others away
and stay clear of mechanical linkages.
1. Press MAXIMUM DUTY CYCLE ICON .
2. Set Max Duty Cycle value to approximately 60
(or refer to FieldPilot manual for desired lock to
lock times).
3. Turn the wheels all the way to the left (or right).
4. Press the GREEN ARROW (or RED ARROW
). This will start a timer below the STOPLIGHT
as well as turn the vehicle to the right (or left).
5. Press the RED STOPLIGHT when the
wheels are all the way to the right (or left). The
time displayed under the STOPLIGHT is the lock
to lock time.
6. Press the PLUS/MINUS ICONS to adjust
the Max Duty Cycle value.
7. Repeat steps 3 through 6.
8. When the time from left to right / right to left (lock
to lock) begins increasing (it takes longer to turn
the tires) press
►CHECKERED FLAG to complete Valve
Setup.
►FIELDPILOT SETUP TAB to return to
main FieldPilot Setup.
NOTE: Press & hold PLUS/MINUS ICONS to
quickly adjust settings.
Figure 2-64: Valve Frequency
The following are common frequencies/valves:
TeeJet Technologies
Part # Valve Frequency
35-02151 FP, CC, NP 2 hz
35-02152 FP, OC, HF, NP 2 hz
35-02153 FP, OC, NP 2 hz
35-02173 FP, PC, LS, NP 2 hz
35-02172 FP, PC, PWM, LS 175 hz
35-02179 FP, PC, PWM, LS 175 hz
35-02180 FP, CC, PWM 110 hz
35-02181 FP, CC, PWM, LS 110 hz
35-02182 FP, CC, PWM 175 hz
35-02183 FP, CC, PWM 1.1 OC 110 hz
35-02184 FP, CC, PWM 7.9 OC 175 hz
35-02185 FP, CC, PWM 2.1 OC 110 hz
35-02186 FP, CC, PWM 4.0 CC 110 hz
35-02187 FP, CC, PWM 7.9 CC 175 hz
For valves manufactured by sources other than
TeeJet Technologies, refer to manufacturer’s
specifi cations for appropriate valve frequency.
Minimum Duty Cycle
Minimum Duty Cycle sets the minimum amount of
drive required to begin steering the vehicle left or
right. Range is 0.0 - 50.0.
RECOMMENDATION – Have a large area of clear
space available to perform test cycles.
NOTE: If the valve frequency is set below 15 Hz
(non proportional), set the amount of drive to
“25.0”. Cycle test is not necessary.
WARNING: PINCH POINT HAZARD!
To prevent serious injury or death, avoid
unsafe practice while manually operating
hydraulic steering circuits. Keep others away
and stay clear of mechanical linkages.
Cycle Left
Cycle Left sets the minimum amount of drive
required to begin steering the vehicle to the left. .
1. Press MINIMUM DUTY CYCLE LEFT ICON .
2. While the vehicle is moving in a slow forward
straight line motion, press the GREEN
STOPLIGHT .
3. Slowly increase the duty cycle number using the
PLUS BUTTON until the vehicle begins to
turn left.
4. Press the RED STOPLIGHT to complete the
left test.
5. Press
►PAGE RIGHT ARROW to proceed to
Minimum Duty Cycle Right.
►FIELDPILOT SETUP TAB to return to
main FieldPilot Setup.
NOTE: Press & hold PLUS/MINUS ICONS to
quickly adjust settings.
- USER MANUAL 1
- CHAPTER 1– PRODUCT OVERVIEW 7
- SYSTEM FEATURES 7
- Matrix 840G Console 8
- SYSTEM COMPONENTS 8
- Matrix 570G Console 8
- RealView Camera 9
- Video Selector Modules 9
- GPS Antennas 9
- FieldPilot 9
- Steering Control Module 9
- 98-05141 R2 10
- CONFIGURATIONS 11
- Engage/Disengage 12
- POWER ON/OFF 13
- Start Up Sequence 14
- GENERAL OPERATION 14
- INFORMATION 14
- Page Layout and Navigation 15
- CHAPTER 2 – UNIT SETUP 16
- Lightbar 17
- Home Menu 17
- SYSTEM SETUP 17
- LED Brightness 18
- Display Mode 18
- Time Zone 19
- Language 19
- Requirements 20
- GPS Status 20
- GPS Type 20
- GPS Port 20
- LCD Brightness 21
- GGA Requirements 21
- Software Version 1.03 22
- Software Version 1.00 to 1.02 22
- Next Power Cycle 22
- Save About Information 23
- Screenshot 23
- Enable/Disable 23
- Capture an Image 23
- About/Save 23
- Four Channel VSM 24
- Eight Channel VSM 24
- BOOMPILOT/SINGLE 25
- BOOM SETUP 25
- BoomPilot Setup 25
- Number of Boom Sections 26
- Boom Section Width 26
- Delay On 26
- Delay Off 26
- VEHICLE SETUP 27
- Single Boom Setup 27
- TILT GYRO MODULE 28
- Valve Setup 30
- FIELDPILOT SETUP 30
- Autosteer 30
- Cycle Right 31
- Maximum Duty Cycle 31
- Minimum Duty Cycle 31
- Cycle Left 31
- Con gure FieldPilot 32
- Valve Test 32
- Deadband 33
- Coarse Steering Adjustment 33
- Fine Steering Adjustment 33
- Lookahead 34
- CHAPTER 3 – GUIDANCE 35
- GUIDANCE OPERATION 35
- Straight A-B Guidance 35
- GUIDANCE BAR & STATUS BAR 36
- Guidance Bar 36
- Curved A-B Guidance 36
- Circle Pivot Guidance 36
- Last Pass Guidance 36
- VEHICLE VIEW 37
- Status Bar 37
- Vehicle View 38
- Guidance Mode Select 38
- Zoom In/Out & 41
- Perspective 41
- BoomPilot 41
- Field View 42
- Field Boundary 42
- FIELD VIEW 42
- Return to Point 43
- Zoom In/Out 44
- World View 44
- Pan Mode 44
- REALVIEW GUIDANCE 44
- RealView Guidance 45
- Full Screen 45
- Guidance Over Video 45
- Steering Angle Indicator 46
- Single Camera Selection 46
- Split Camera View 47
- Guideline Adjustment 48
- CHAPTER 4 – MONITORING 49
- JOB VIEW 49
- Job Information 49
- Save Information 50
- BOOM MONITORING 51
- Boom Monitor 51
- APPENDIX A ICON REFERENCE 53
- Menu Options 53
- CHAPTER 5 – APPENDIX 53
- Unit Setup 54
- Job View 55
- Guidance Screens 55
- APPENDIX B TIME ZONES 56
- APPENDIX D UNIT 57
- SPECIFICATIONS 57
- APPENDIX C FACTORY 57
- SETTINGS & RANGES 57
Produits connexes et manuels pour Ordinateurs Teejet Matrix 840G User Manual
(2 pages)
(2 pages)
(2 pages)
(2 pages)
(2 pages)
(127 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels