Teejet RX 400p Manuel d'utilisateur télécharger pdf (Page 142)

RX 400p

98-05044 9-4

Figure B-3 illustrates the required interface between the RX 400p and an external

GPS receiver:

3 RX RTCM

5 GND GND

AUX

External Correction Source

Figure B-3 External Correction Source Interface

Note - For successful communications, the baud rate of the RX 400p AUX port

must be set to match that of the external correction source. Additionally, you

must interface the RX 400p to an RS-232C serial port of the external source.

Refer to Section 4.15.3 for instructions related to setting the RX 400p baud rate.

1 2 ... 137 138 139 140 141 142 143 144 145 146 147 ... 150 151

RX 400p 1
Copyright Notice 3
Trademarks 3
MID-TECH Limited Warranty 4
List of Figures 13
List of Tables 14
Preface 15
Organization 16
Customer Service 17
World Wide Web Site 18
Document Conventions 19
1 Installation 21
1.3.1 Receiver Placement 22
1.3.3 Power Considerations 23
1.3.5 Grounding the RX 400p 24
External Device 26
1.5 Mounting Accessories 31
2 RX 400p Overview 33
2.2 WAAS Operation 34
2.3 OmniSTAR Operation 35
2.4 Beacon Operation 36
2.4.2 Receiver Performance 38
Table 2-2 Preset DGPS Mode 40
3 RX 400p Architecture 41
3.3 Applications 42
4 Operation 43
4.3 Menu Access Icon 44
4.4 Receiver Status Icons 44
% & ^ 45
4.4.3 OmniSTAR Lock Icon 46
4.4.4 Beacon Lock Icon 47
4.4.6 Autonomous Mode Icon 48
Figure 4-9 GPS Menu 49
Figure 4-10 WAAS Menu 50
Figure 4-11 OmniSTAR Menu 50
4.6 Start-Up Sequence 53
4.7.1 WAAS Mode Bar Chart 54
4.7.3 Beacon Mode Bar Chart 55
4.8 Main Menu 56
4.9 GPS Menu 57
4.9.2 GPS Satellites Menu 73
4.9.3 GPS Configure Menu 75
4.10 WAAS Menu 81
4.11 OmniSTAR Menu 86
4.12 Beacon Menu 96
Health Code Indication 101
4.13 External RTCM Menu 103
4.14 Autonomous Menu 105
4.15 System Setup Menu 106
4.15.2 Display Format Menu 108
4.15.3 Baud Rates Menu 110
400p receiver: 113
4.17 Firmware Updates 116
5 Configuration Wizard 117
5.1 Start-up Sequence 119
5.6 Saving a Configuration 120
RX 400p 121
6 NMEA 0183 Messages 123
6.4 SLXMon 124
6.5 GPS NMEA Data Messages 125
6.5.2 GLL Data Message 126
6.5.3 GSA Data Message 127
6.5.4 GST Data Message 128
6.5.5 GSV Data Message 128
6.5.6 RMC Data Message 129
6.5.7 RRE Data Message 130
6.5.8 VTG Data Message 131
6.5.9 ZDA Data Message 131
7 Troubleshooting 133
9 Appendix B - Interface 139
9.2 RTCM Data Output 140
2 TX RTCM 141
5 GND GND 141
Separate GPS Receiver 141
3 RX RTCM 142
External Correction Source 142
OmniSTAR DGPS Service 143
10.2.2 Contacting OmniSTAR 144
11 Appendix D - Beacon 147
Information 147
Further Reading 148
12 Index 149

Commentaires sur ces manuels

Pas de commentaire

Teejet RX 400p Manuel d'utilisateur Page 142

Commentaires sur ces manuels

Produits connexes et manuels pour Ordinateurs Teejet RX 400p