Teejet Legacy 6000 Manual Manuel d'utilisateur Page 91
- Page / 159
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 4 - Operation86
System Messages
System messages do not obstruct operation. The most common system messages
are “system ready” messages that occur when the system is operating properly.
Figure 4-10: System Message
Warning Messages
Warning messages do not obstruct operation (e.g., product application rates,
speed). An alarm will sound when a warning message is displayed. The alarm can
be muted by pressing the Alarm Silence softkey. The warning message will remain
until the situation is resolved. The alarm will not sound again unless a new warning
is issued (for example, low bin or pressure if these are monitored).
Figure 4-11: Warning Message
Indicates what is occurring during
normal system operation
Alarm Silence
softkey (F10)
Warning
Message
- TABLE OF CONTENTS 2
- CHAPTER 1 - INTRODUCTION 6
- SYSTEM FEATURES 6
- Chapter 1 - Introduction2 7
- System Components 8
- Switch Function Module 9
- Input Status Module 10
- FieldPilot Module 10
- SWATH MANAGER 5 (SM5) 11
- LEGACY 6000 CONFIGURATIONS 11
- +12v Onl y 12
- Chapter 1 - Introduction8 13
- 45-053 40 14
- 45-081 06 45-081 06 14
- Chapter 1 - Introduction10 15
- CHAPTER 2 - SYSTEM OVERVIEW 16
- INITIAL POWERUP 17
- Chapter 2 - System Overview14 19
- Forward Arrow 19
- PAGE LAYOUT AND NAVIGATION 20
- SYSTEM SETUP 22
- Console Setup 23
- Lightbar Setup 24
- GPS RECEIVER SETUP 25
- Implement Setup 26
- Chapter 2 - System Overview22 27
- CHANNEL SETUP 29
- Channel Favorite 30
- Application Type 31
- Application Type Settings 32
- Drive Type 33
- Chapter 2 - System Overview30 35
- Primary Sensor 37
- Primary Sensor Settings 38
- SECONDARY SENSOR 39
- Settings Description 40
- Monitor Selection 41
- Monitor Settings 42
- Channel Setup Completion 43
- Saving Channel Setup 44
- FIELDPILOT SETUP 45
- FieldPilot Calibration 46
- Adjust Oil Flow 47
- Drive Straight A-B Line 48
- Chapter 2 - System Overview44 49
- Chapter 2 - System Overview46 51
- Bullseye 52
- STARTING JOBS 53
- Manually Naming Jobs 54
- Automatic Job Naming 55
- No PCMCIA Card 55
- ARM LAUNCHER 56
- Calibration Procedure 57
- PRIME INJECTION SYSTEM 58
- )NJECTION 59
- 0RIMING3YSTEM 59
- Prime State Reset Values to 0 60
- JOB REPORT SETUP 62
- Item Description 63
- ARM SETUP 64
- Entering File Names 66
- Swath Manager Lookahead 66
- CAN Switchbox 68
- Input Status Module (ISM) 69
- Swath Manager 5 70
- PRODUCT SETUP 71
- Product Name Selection 72
- Variable Rate Application 73
- Tilt Sensor Functions 76
- Antenna Height 78
- Tilt Sensor Calibration 79
- Next softkey (F6) 80
- CHAPTER 4 - OPERATION 82
- PRODUCT APPLICATION 82
- GPS/BOUNDARY PAGE 83
- Rate Adjustment 84
- Test Speed 85
- Reset Initial Quantity 85
- FieldPilot Adjustments 86
- The Map Page 87
- Product Control 88
- Chapter 4 - Operation84 89
- Solid and Boom Patterns 90
- System Messages 91
- Warning Messages 91
- VEHICLE GUIDANCE 92
- Changing Guidance Patterns 93
- Straight-Line A-B Guidance 93
- Curved A-B Guidance 95
- Headland Guidance 96
- Ignore Headland Guidance 98
- Chapter 4 - Operation94 99
- Headland Off 99
- Ignore Headland 99
- Circle Pivot Guidance 100
- Chapter 4 - Operation96 101
- Mark B softkey 101
- Legacy 6000 102
- 98-05053 R2 102
- FIELDPILOT 103
- LIGHTBAR 104
- Applied Area Detection 105
- MAPPING FIELD BOUNDARIES 106
- MAPPING POINTS AND HAZARDS 107
- Points Mapping 108
- Hazard Mapping 108
- EXITING OPERATION 109
- SHAPE FILES 110
- FIELDWARE MAP MANAGER 111
- LIGHTBAR INDEX 111
- Chapter 4 - Operation108 113
- CHAPTER 5 - SYSTEM TOOLS 114
- DEVICE MANAGER 114
- Backup Files 115
- Restoring System Files 116
- Importing Files 116
- Speedometer 117
- Swath Manager LED Brightness 118
- Channels 119
- GPS Receiver 121
- LightBar 121
- Channels 1,2,3 122
- CARD MANAGER 123
- Chapter 5 - System Tools120 125
- CHAPTER 6 - MAPPER 126
- DATA SETUP 126
- New Job Creation 127
- Existing Job Selection 127
- Naming Jobs Automatically 127
- MAPPER SETUP AND MARKERS 128
- Chapter 6 - Mapper124 129
- Object Name Creation 130
- Object Names Folders 131
- MAPPER APPLICATION 132
- Chapter 6 - Mapper128 133
- Information Page 134
- MAPPER TOOLS 135
- MAPPER OPTIONS 136
- CHAPTER 7 - EXT 138
- GUIDANCE ONLY MODE 138
- LOG DATA MODE 138
- RATE CONTROL MODE 139
- RATE CONTROLLER 140
- Entering Offset Direction Y 141
- Entering Offset Distance Y 142
- CONTROLLER SETUP 143
- Arrow keys 144
- Enter button 144
- PRODUCT SETUP OPERATION 145
- Product Setup Wizard 146
- Select Prescription Map Layer 146
- RATES PAGE 147
- EXITING OPERATIONS 148
- Chapter 7 - EXT144 149
- Using the Calibration Table 155
- APPENDIX C - NH3 APPLICATION 158
Produits connexes et manuels pour Ordinateurs Teejet Legacy 6000 Manual
(194 pages)
(6 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels